精品九九人人做人人爱-欧美国产激情18-久久se精品一区精品二区-国产精品福利一区二区

PU Sandwich Panel Line - PIR Sandwich Panel Production Machine - Sinowa

Debugging Method of Cold Roll Forming Machine

Author: Sinowa/Post Date: 2021-07-22/Keywords: Cold Roll Forming Machine

The commissioning of Cold Roll Forming Machine needs good working experience. In order to make it more convenient for us to master the debugging method of Cold Roll Forming Machine, we specially compiled the following manual for your reference, introducing some methods of Cold Roll Forming Machine debugging frequently encountered in daily work. The following methods are applicable to roll design, which is reasonable because of the long time, Or not familiar with the cause of debugging confusion, re debugging normal back. However, if the roller design is unreasonable when leaving the factory, it is necessary to modify the roller. If the roller design is unreasonable, it is very difficult to debug. Therefore, if it is a roller problem, the manufacturer should be contacted to modify the roller.

Cold Roll Forming Machine

In the daily use of Cold Roll Forming Machine, the common problems are: twist, edge wave, longitudinal bending and so on. Such a problem is that the force on each force point of the roll is not balanced, and the left and right roll deviation is not in a straight line. Therefore, when debugging the cold bending machine, we should grasp a central point to consider the problem, that is, the roller must be in a straight line, and the upper and lower clearance of each group of rolls should be consistent. Therefore, when the Cold Roll Forming Machine has problems, we should focus on this central idea To debug. So, what kind of method can make the roller midpoint in a straight line, and how can the gap between the upper and lower rollers be the same? The following methods will be used for you.

Cold Roll Forming Machine

A method of keeping all rolls in a straight line. First determine the first group and the last group of center point, the two groups of roller center point left and right transfer to the center. Then draw a straight line according to these two points. Mark the center point with chalk, and then mark the center point with the center caliper. Mark the center point of all down rolling on the machine in the same way, and then adjust all the center points of the roller to the straight line. After the lower roll is straightened, install it back to the upper roll.

Cold Roll Forming Machine

The method of adjusting the gap between the upper and lower rollers. We should prepare a small section of raw materials for production, the thickness of which is consistent with the material used in ordinary times, and then cooperate with a small mirror and a flashlight. Put the material between the upper and lower rollers, and then tighten the screws on the left and right sides at the same time. It should be noted that one side should not be tightened first and then the other side, which may cause the gap on both sides inconsistent. After tightening, use a mirror to look at one side to see if the gap just fits. At the same time, use a flashlight on the other side. If the gap is not uniform, the light transmission will be uneven. After confirming that the gap is even, loosen it a little, and it is appropriate to take out the material just put in. At this time, lock the screws on the left and right sides. Try to adjust the clearance in the same way.

Cold Roll Forming Machine

After mastering the above core methods, we should flexibly use different methods for different problems. Sometimes when there are some problems, we can’t pull the straight line again according to the above method every time, which will be very time-consuming and laborious. When there is a slight problem, we can check the material passing through the pass one by one. In this way, we can know from which group the problem began. When the material head just enters the roller, we can roughly see which group is not in the same straight line on-line. Or check the clearance in groups with method 2. When there is twist or edge wave, it may be that a group or groups of left and right pressure are inconsistent or not in a straight line. When longitudinal bending occurs, it may be that some groups of pressure are too tight. You can use different debugging methods according to different situations, slowly summarize, after a period of time, you will be handy.

Page Url: http://m.shionoe.com/en/debugging-method-of-cold-roll-forming-machine.html

You are here: Home / News / Debugging Method of Cold Roll Forming Machine
Contact Us
Email: sinowa@sinowa.cn
Call: +0086 151 0610 6366
Add: High-tech Industrial Development Zone, Zhenjiang, China
主站蜘蛛池模板: 无码中文人妻在线一区| 少妇无码一区二区二三区| 亚洲最大av网站在线观看| 免费精品一区二区三区第35| 粗大猛烈进出高潮视频| 亚洲v无码一区二区三区四区观看| 亚洲色婷婷六月亚洲婷婷6月| 久久成人国产精品| 青青草原综合久久大伊人精品| 麻豆天美国产一区在线播放| 日产乱码一二三区别免费麻豆 | 特级欧美午夜aa片| 亚洲国产成人精品无码区花野真一 | 免费中文熟妇在线影片| 最近的中文字幕在线看视频| 亚洲乱码中文字幕久久孕妇黑人| 小少呦萝粉国产| 欧美老熟妇乱人伦人妻| 三年片在线视频中国| 亚洲va成无码人在线观看| 欧美日韩一区二区综合| 欧美成人精品三级网站| 亚洲av无码片一区二区三区| 奇米在线7777在线精品| 污污内射在线观看一区二区少妇| 国产精品亲子乱子伦xxxx裸| 中文字幕无码人妻aaa片| 男吃奶玩乳尖高潮视频| 亚洲av无码国产精品色午夜洪| 国产午夜福利久久精品| 精品无码久久久久久久久久| 用舌头去添高潮无码视频| 国产欧美精品一区二区色综合| 亚洲欧美色中文字幕在线| 日本在线视频www鲁啊鲁| 欧美饥渴熟妇高潮喷水水| 亚洲h在线播放在线观看h| 美女裸体a级毛片| 小荡货奶真大水真多紧视频| 久久久久人妻一区精品性色av| 任我爽精品视频在线播放|